Welcome to the Forum, @emrichardt! ![]()
I wonder about the physical installation of your Bulb Cam and Accessory Bulb and if you’re experiencing interference with the Bluetooth Low Energy (BLE) signal. I think that’s been my problem, and I think a number of factors are contributing.
In my installation, I have three external sockets on a circuit controlled by a single switch inside the front door of the home. One socket is in a light fixture on the front porch. The other two are on either side of the garage door, facing the driveway. I have a Bulb Cam in the garage socket closest to the porch, so it’s effectively between the Accessory Bulbs in each of the other two sockets. The sconces facing the driveway have some metal in them, perhaps enough to create a partial Faraday cage effect, so I wonder how much that might interfere with the radio signals. The farthest Accessory Bulb, on the other side of the garage door, is the one that I’ve usually seen “offline” and with its light on.
Steps I’ve taken to re-bind the Accessory Bulb to the Bulb Cam when I’ve seen this happen (not necessarily in this order; sometimes multiple items in combination):
- Delete the “offline” Accessory Bulb and try to re-pair. (This by itself usually fails.)
- Delete both Accessory Bulbs and try to re-pair. (This often resolves the issue but isn’t always sufficient by itself.)
- Restart Bulb Cam from the app’s Settings screen. (I believe at times just rebooting the Cam this way has resolved the issue for me.)
- Power-cycle the circuit (which cuts and restores power to Bulb Cam and two Accessory Bulbs).
- Open the garage door. (It seems weird, but it often helps. My hypothesis is that there’s enough metal in both the sconces and the door that opening the door to move metal out of the way between the Bulb Cam on one side of the door and the Accessory Bulb on the other side is enough to improve the BLE signal between the two devices. I don’t know for sure if this provides any real benefit to my other troubleshooting steps, but I decided to try it one day and it seems to result in success more often when I’ve tried and failed with the other steps while the door is closed. Although the garage door itself isn’t line-of-sight between the Bulb Cam and Accessory Bulb, its presence along and near that line-of-sight path seems close enough that it might cause problems. If I open the door and then try other steps listed above, that usually resolves the problem.)
I did notice one “offline” instance with an Accessory Bulb while I was out of state for Christmas. I wasn’t able to visually confirm the “offline” bulb’s state (to see if the light was actually on), but I was able to resolve the issue that time by un-binding/re-binding both Accessory Bulbs. I may have also rebooted the Bulb Cam at that time, but I don’t recall. Everything seemed normal (lights off) when I arrived home during the day a few days later.
I have also noticed less frequent “offline” instances since doing three other things:
- I made some changes to my Wi-Fi network and now have a range extender in the garage. I wouldn’t expect this to have a profoundly direct effect on the BLE performance, but….

- The problematic Accessory Bulb is currently in a Lamp Socket v2 because I wanted to put a Cam OG out there temporarily and that was an easy way to power it. Because of that addition between the bulb and the sconce’s socket, that particular Accessory Bulb now sits lower in the sconce, so maybe that’s enough to improve its signal.

- Because I want the Accessory Bulbs to be on at night to provide overnight lighting with Bulb Cam’s Ambient Light setting, I need that Lamp Socket v2 to have its socket turned on overnight. In order to do that, I have to enable that Lamp Socket v2’s Ambient Light setting, and on Lamp Socket v2 enabling Ambient Light requires setting a schedule.
I set the schedule for 12:01 p.m.–12:00 p.m. so that I’d have a powered socket all night—basically all day except for a minute in the middle of the day. Effectively this means that every day at noon that particular Accessory Bulb reboots (power cycles) because Lamp Socket v2’s Ambient Light turns off for that 1 minute.
You might consider things like your sconce construction, distance between your Bulb Cam and Accessory Bulb, Wi-Fi signal, garage door or other potential sources of metallic interference (?), or other factors I haven’t even considered. Without knowing more about your situation and what you’ve tried with Wyze Support’s guidance, I’m not sure what else to suggest at this point.