I just got my Wyze Cam Pan v3. Excited I replaced my Cam v3 looking outside from second floor on to my driveway with Cam Pan v3. However my excitement didn’t last very long when I encountered these two issues which are really disappointing to say the least. Even though I have defined motion det…

ok ben on the new beta firmware since its release. all seamed good until today. i have reset the home positioin 4 times today. I have motion tracking on only and have waypoints set but not scanning to them at the moment. the cam is mounted upside down. so now it seams to be returning right to left o…

For this next test, I have removed all waypoints and turned off scan. Using Motion Tracking and DZ only. Will post results tomorrow.

Something else I am noticing. I have one waypoint set. This is the position I set the waypoint to: [image] If I then go to the Live stream page and scroll to the far left side, then tap the waypoint to reset back to that view above, it is slightly off to the left in where it returns to: [image] S…

that is how mine is set and up till this afternoon it was doing quite well, but have had to set it 4 times its been few hours and it is still ok, but in fairness the wind has calmed down and it has not been moving as much. i’ll test more as i have time.

Mine is also mounted upside down from under my eave, so up is down… Just checked it and it was off. I went to the DT to get a measurement of how far in what would normally be a downward direction (up in my case). However, two issues. First, my detection zone has been turned off. I’m restarting it t…

Test #2. All waypoints deleted. Pan Scan Off, Detection Zone On. Track Motion on. Home Point set last night at @ 8:45: [Screenshot_20230216-150523-322] Checked at 7:27 this morning: [Screenshot_20230216-150557-956] Checked again at 3:30 moments ago. [Screenshot_20230216-150628-887] Screen …

Mine is still drifting up slowly (or down in my case since it’s mounted upside down). It is certainly better than it was as before the beta firmware, it wouldn’t even return to the home position reliably. Now with the beta firmware at least it does that, just not the exact same point. So it drifts.

so far todaymine has been returning to correct home point. but i did notice that the skip at 5 seconds is still there. hadn’t noticed it last couple days, but it is back

Getting the skip too. Just started yesterday. On the latest firmware. No beta. Mine still drifts after tracking motion.

The Android App has a setting in Account → App Settings → Enable Hardware Decoder that will shift video processing of live stream and playback to the device’s onboard Graphic Processor Chip. I have found it to be absolutely invaluable for maintaining fluid video, especially with the V3Pro. Give it…

Wyze Cam Pan v3 - Does not return back to home position

Cameras

SlabSlayer February 16, 2023, 8:12pm 80

Test #2. All waypoints deleted. Pan Scan Off, Detection Zone On. Track Motion on.

Home Point set last night at @ 8:45:

Checked at 7:27 this morning:

Checked again at 3:30 moments ago.

Screen capture showing the return to home point:

Topic		Replies	Views
Cam Pan V3 DZ and Pan Scan issue Cameras android-and-ios , cam-pan-v3	67	768	October 5, 2024
Wyze Cam Pan v3 Drift Update Wyze News important , cam-pan-v3	33	5751	April 27, 2024
Wayz Pan Cam v3 SD cards and detection zones Cameras android , cam-pan-v3	27	319	April 30, 2025
Camera Doesn't stay where aimed Cameras cam-pan-v1	34	22278	August 5, 2020
Wyzecam pan v3 doesn't return to detection zone position if motion tracking enabled Cameras cam-pan-v3	12	1339	December 12, 2023

Wyze Cam Pan v3 - Does not return back to home position

Related topics